USB 3.1 Type C to M2 NGFF SSD Raid External Enclosure Case Box 10Gbps Aluminium For Sale
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
USB 3.1 Type C to M2 NGFF SSD Raid External Enclosure Case Box 10Gbps Aluminium:
$38.98
USB 3.1 Type C to M2 NGFF SSD Raid External Enclosure Case Box 10Gbps Aluminium
Two NGFF interfaces can be extended simultaneously through the USB3.1 type-c interface, and two NGFF interfaces can connect two SSDS of 3030 or 3050 specifications at the same time. Raid0,Raid1, or PM patterns can be formed between two SSDS.
Features:
1. USB3.1 Type-C interface: lr31-1352s adopts the USB3.1 Type C interface recently promoted by APPLE, Intel, asustek and other famous manufacturers. The theoretical transmission speed reaches 10Gbps. The transmission speed of USB3.0 is 1 times faster than that of USB3.0. At the same time, USB3.1 TYPE C interface supports forward and backward plug.
2. Compatible with SSD specification: lr31-1352n compatible with SSD of NGFF(M.2) interface. At present, there are mainly four sizes of NGFF(M.2) SSDS in the market by volume, which are 2230, 2242, 2260 and 2280 respectively. PCB board is suitable for NGFF (M.2) hard disks of 2230, 2242, 2260 and 2280 specifications.
3. Working mode setting of SSD: lr31-1352n supports Raid0,Raid1 and PM working modes. In general, the factory\'s default shipping mode is Raid0, and the factory work Settings can also be changed according to customer requirements.
Specification:
Condition: 100% Brand New
Color: Silver
Size: Approx. 10.8 * 5 * 1.1 cm / 4.2 * 1.9 * 0.4 inch
32.5 cm (USB Cable Length)
Product Name: USB3.1 Type C to 2Ports NGFF(M.2) SSD Raid Hard Disk Box
Model Number: LR31-1352N
Transmission Interface: USB3.1 Type-C 10Gbps
Built-in Interface: NGFF(M.2) *2
Shell Material: Aluminum Magnesium Alloy
Supported Modes: Raid0,Raid1,PM
Support System: For All WINDOWS/ For Linux/ For
Support Hard Disk Type: Applicable to SATA protocol KEY B NGFF SSD
Weight: Approx. 128 g
The RAID0 setup steps are as follows:
Insert the hard drive that set RAID0 for the first time into the computer, which automatically installs the hard drive when it detects the hard drive hardware. The installation will be completed automatically around 10S. For the first time, we first initialize and partition the hard disk:
Mouse over my computer, right click, select: management-disk management, we can find that the computer has an additional uninitialized disk.
Mouse over the uninitialized disk, then right-click, select: initialize disk
Enter the initialization disk interface, and select the options that need to be set
After the initialization is complete, the next partition is made, the mouse is moved to the unpartitioned hard disk, and then the right click is selected
Raid1:
This is actually a disk image. In Raid1 mode, when two SSDS are connected at the same time, the two disks appear as the primary and backup disks, and by default are small disks. The backup disk is automatically backed up at the same time during the operation of the main hard disk, making the data more stable. As shown in the figure below: when two 256GB SSDS are connected at the same time, the capacity is 223GB
Since the initial partition of the RAID1 hard drive is the same as the operation of RAID0, we omit it here
PM:
Also called disk array, each disk is separate from the other. When two SSDS are connected at the same time, the capacity and speed of the two disks remain unchanged. As shown in the figure below: when two 256GB SSDS are connected at the same time, the capacity is 223GB and 223GB respectively
Since the initial partition of the PM hard drive is the same as RAID0, we omit it here
Installation Steps:
1. First determine the specifications of the SSD is 2230\\2242\\2260 or 2280, normally when the pillars of the default location of delivery for the 2280. If your SSD is 2230/2242, or 2260, you need to exit the pillars moving on the proper positioning, one of the first with you purchase often-expensive hold the copper bar at the bottom of the hexagonal position, another hand grasping the positive hexagon nut immediately to the left can exit the copper cylinder and copper nut. Move the exit copper column and copper nut to another specification positioning hole.
2. Check the syringe Settings for the working mode of the SSD you want to set (be very careful here, misoperation will cause data loss). Also remember the locations of SSD1 and SSD2 so that the working state of SSD can be checked later
Cover the back cover and tighten the screw with the cross screwdriver to fix the back cover
Plug in the USB3.1 data line and check the working status of each SSD
* LED1 is always bright, indicating that SSD1 has been detected by the computer, and LED1 keeps flashing, indicating that SSD1 is in the writing or reading state. Otherwise, it is abnormal
* LED2 is always bright, indicating that SSD2 has been detected by the computer, and LED2 keeps flashing, indicating that SSD1 is in the writing or reading state. Otherwise, it is abnormal
Test Report:
Speed is not fixed. There are many factors influencing speed, such as test software, test equipment, host, wire, etc. The following test software is: ATTO Disk Benchmark, test hard Disk
Package List:
1 * HD Box
1 * Screwdriver
1 * USB3.1 to USB3.0 Data Line
Note:
1.Please allow 1-3 cm error due to manual measurement. Thanks for your understanding.
2.Monitors are not calibrated same, item color displayed in photos may be showing slightly different from the real object. Please take the real one as standard.
2.We only ship item to your PayPal verified address.
3.Payment must be received within 3 days from the date of purchase.
4.Orders will be processed instantly and dispatched in same day normally, so we do NOT accept any
Email/Message note after you place orders.
Terms Of Sales 1.Our listing price includes the value of goods,packaging cost,and export taxes,not including international import duties.
2.Import duties,taxes,and charges are not included in the item price or shipping fee.
3.The import duties are buyers\' responsibility.Please check with your country\'s customs office determine what these additional costs will be prior to your purchase.
4. All disputes arising from the import duties will be submitted to for solution.
response 1.Any questions, pls. contact us via message or email us.We will reply your message within 48 hours. If you do not receive our reply within 48 hours, pls. post a message again because sometimes our message system may block some emails.
2.If you are satisfied with our service, pls. kindly leave us a positive response and give us the Detailed Seller Rating with all \"5 stars\" in very area.
3.Our aim is to provide Top Level Customer Service, your recognition will encourage us greatly and serve you better.We strive to keep all our customers satisfy.
4.We greatly appreciate your POSITIVE response. Please do NOT leave negative response without asking for help.Thanks!
We will always do our up most to exceed your expectations in customer service, communication and dispatching of your orders.
